Lanner FW-7525 Manual de usuario

Network Application PlatformsHardware platforms for next generation networking infrastructureFW-7525V1.1User's ManualRelease Date: 2015/05/08

Chapter 2: Motherboard InformationBlock DiagramThe block diagram depicts the relationships among the interfaces or modules on the motherboard. Pleas

Motherboard LayoutThe motherboard layout shows the connectors and jumpers on the board. Refer to the following picture as a reference of the pin assig

Jumper Settings & Connector PinoutsFan Connectors(FAN1 ): The 5-pin connector is for connecting the CPU fan. Keyboard and Mouse Connector (PKMB1)

GPIO Output Pin (GPIO1): Theses pins can be used to write to an internal register to control the GPIO output pin state.SPI-ROM Update Connector (SPIR

SO-DIMM Socket (CN1): The 204-pin DDR3 SO-DIMM is for connecting the Non-ECC DDR3 1333/1600 memory. The system can support up to 8 GB in maximum. SAT

PCIe Expansion Connector (MPCIEC1): Mini-PCIe connectorPIN NO. Signal PIN NO. Signal1 PMU_WAKE# 27 GND2 VCC3 28 1.5V3 NC_RSV1 29 GND4 GND 30 SMB_CLK5

Chapter 3: Hardware SetupPreparing the Hardware InstallationTo access some components and perform certain service procedures, you must perform the f

3. Place an SSD on the bracket as shown below.4. Turn the bracket and the SSD around and align the 4 screw holes. Then, secure the SSD onto the brack

Installing FW-7525 on the WallFW-7525 can be mounted on the wall by using optional mounting kit. The following will present steps of wallmounting FW-7

Installing FW-7525 on a RackFW-7525 can be mounted on a wall by using optional mounting kit. Please read the precautions first.1. Elevated Operating A

OverviewIcon DescriptionsThe icons are used in the manual to serve as an indication of interest topics or important messages. Below is a description

4. Attach the ears of the L-shaped brackets to the rack and then apply long threaded nails.Notes: rack-use screws and nuts are not supplied in the mou

Chapter 4: BIOS SettingsAccessing the BIOS menuWhen you are installing a motherboard or when the system prompts “Run Setup” during start-up, you will

The Main MenuThe main BIOS setup menu is the first screen that you can navigate. Each main BIOS setup menu option is described in this chapter.The Mai

Advanced SettingsSelect the Advanced tab from the setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left fr

Super IO configurationSerial Port 0/1 ConfigurationItem SelectionSerial Port Enable or disable this serial portDevice SettingsShows the serial port ba

HW MonitorThis menu shows the hardware monitor configuration settings. Select an item then press <Enter> to display the configuration options.PC

Serial Port Console RedirectionUse this menu to set the settings for BIOS remote access feature. Item SelectionConsole Redirection Enable or disable B

Lanner Generation 2 LAN Bypass ConfigurationIn this screen, you can configure the Lan Bypass functionality. The system can accommodate one LAN module.

USB Configuration You can use this screen to select options for the USB Configuration. Use the up and down <Arrow> keys to select an item. Use t

USB Mass Storage DrivIn this option, you can enable or disable the attached USB drive to be used as the system’s hard drive.USB Hardware Delays a The

LITHIUM BATTERY CAUTION: Risk of Explosion if Battery is replaced by an incorrect type. Dispose of used batteries according to the instructionsOperat

Intel RCSetup You can use this screen to view the capabilities and of your CPU. You can also use this menu to enable/disable certain functions of your

North Bridge Chipset ConfigurationIt shows the memory information such as the total detected memory and memory frequency.South Bridge Chipset Configur

Item SelectionAHCI Mode Set to AHCI mode when you want the SATA hard disk drives to use the AHCI (Advanced Host Controller Interface). The AHCI allows

Security SettingsSelect Security Setup from the Setup main BIOS setup menu. All Security Setup options, such as password protection and virus protecti

Boot ConfigurationIn this screen, you will be able to configure the boot procedures and the related elements.Items OptionsSetup Prompt Timeout Specify

Save & ExitSave and ExitSelect the Exit tab from the setup screen to enter the Exit BIOS Setup screen. You can display an Exit BIOS Setup option b

Appendix A: Programming Watchdog TimerA watchdog timer is a piece of hardware that can be used to automatically detect system anomalies and reset the

Appendix C: Programming Generation 2 LAN BypassLanner Generation 2 BypassLanner Generation 2 bypass is configured through the BIOS menu as shown belo

Table 1: System Off Bypass is set to enabled Bypass settings in the BIOSSystem StatusRuntime LAN Bypass for the bypass pairSystem off LAN Bypass for

Appendix D: Installing Intel QuickAssist Software for LinuxThe FW-7551 platform incorporates Intel QuickAssist Technology, which includes acceleratio

Sécurité de fonctionnement L’équipement électrique génère de la chaleur. La •température ambiante peut ne pas être adéquate pour refroidir l’équipeme

Appendix E: Terms and ConditionsWarranty Policy All products are under warranty against defects in 1. materials and workmanship for a period of one

RMA Service Request Form When requesting RMA service, please fill out the following form. Without this form enclosed, your RMA cannot be processed.

Table of ContentsChapter 1: Introduction 6System Specifications 6Package Contents 7Optional Accessories 7Front Panel Features 8Rear Panel Featur

Chapter 1: IntroductionThank you for choosing Lanner FW-7525. FW-7525 is a fanless desktop network security system utilizing the cutting edge capabi

Certications/ComplianceCE Class B, FCC Class B, RoHSOrdering InformationFW-7525AFanless Network Security Appliance with Intel® AtomTM processor C2358

Front Panel FeaturesF4F1F2F3 LAN1 LAN2 Intel i210AT Intel i210AT

Rear Panel FeaturesR2R1R3R1 Reset SwitchThe reset switch can be used to reboot the system without turning off the power. R2 ATX Power-on button with L