Lanner LEC-2110 Manual de usuario

>>Hardware Platforms for Embedded and Industrial ComputingLEC-2110User's ManualPublication date: 2012-03-06Embedded & Industrial Comp

10Board LayoutChapter 3Embedded and Industrial ComputingChapter 3: Board LayoutExternal ConnectorsThe following picture highlights the location

11Board LayoutChapter 3Embedded and Industrial ComputingInternal Connectors and JumpersThe following picture highlights the location of internal co

12Board LayoutChapter 3Embedded and Industrial Computing Connectors and Jumpers ListThe tables below list the function of each of the board

13Board LayoutChapter 3Embedded and Industrial ComputingSC2T1, SC2T2: Select COM2 Protocol SettingRS-232 RS-422RS-485SwitchProtocolSC2T1 SC2T2RS-232(D

14Board LayoutChapter 3Embedded and Industrial Computing SW2: Select COM2 and COM3 Termination in RS-485 This switch is used to e

15Board LayoutChapter 3Embedded and Industrial ComputingMini PCI Express Connector (MPCIE1):Pin No. Description Pin No. Description1 WAKE# 2 +3.3V3 RS

16Board LayoutChapter 3Embedded and Industrial ComputingDVI-D Connector (DVI1): A single link DVI-D ConnectorPin No. Description Pin No. Description1

17Board LayoutChapter 3Embedded and Industrial ComputingDC_IN CONNECTOR (CN1): A Phoenix connector for external power supply.Power and HDD LED (

18Hardware SetupChapter 4Embedded and Industrial ComputingChapter 4: Hardware SetupPreparing the Hardware InstallationTo access some components and p

19Hardware SetupChapter 4Embedded and Industrial ComputingPCI/PCIe Riser Card InstallationThe system can accommodate one PCI or PCIe expansion (only o

2AboutAboutEmbedded and Industrial ComputingOverviewIcon DescriptionsThe icons are used in the manual to serve as an indication of interest topics

20Hardware SetupChapter 4Embedded and Industrial Computing 32PCIePCIPCIe

21Hardware SetupChapter 4Embedded and Industrial ComputingInstalling the Hard DiskThe system can accommodate one Serial-ATA disk. Follow these steps t

22Hardware SetupChapter 4Embedded and Industrial ComputingWall MountingThe product ships with wall mounting kit. To mount your product on the wall, f

23Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AAppendix A: Programming Watchdog TimerA watchdog timer is a piece of ha

24Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AChoose to select the hardware Manually8. Choose Show all device and click Next.

25Programming Watchdog TimerEmbedded and Industrial ComputingAppendix ASelect the Lanner IO driver and click Next.14. Click Next15. Click 16. Complet

26Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AOn LinuxExecuting the commands through the Command Line:1. wd_tst --swtsr (Set

27Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AWatch Dog sample code:#include “../include/config.h”#include “../include/versio

28Programming Watchdog TimerEmbedded and Industrial ComputingAppendix A#endif#if BYPASS_PAIR_NUMBER == 5char pair_str[16]=”[1|2|3|4|5]”;#endifvoid pri

29Programming Watchdog TimerEmbedded and Industrial ComputingAppendix A if ( (tmp < 1) || (tmp > 255)) { p

TTaTTable of Contentsbeable of Contents3Chapter 1: Introduction 4System Specication . . . . . . . . . . . . . . . . . . . . .

30Programming Watchdog TimerEmbedded and Industrial ComputingAppendix A#endif }/******** Set runtime bypass enable ****************************

31Programming Watchdog TimerEmbedded and Industrial ComputingAppendix A } //--srbd/******** Set system-off bypass enable **********************

32Programming Watchdog TimerEmbedded and Industrial ComputingAppendix A } //--sobe#endif //>0 else { printf(“<<<Error: Unknow

33Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingAppendix B: Digital Input/Output Control on the GPIO portThe Digitanl I/O on

34Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingChoose to select the hardware Manually8. Choose Show all device and click Nex

35Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingSelect the Lanner IO driver and click Next.14. Click Next15. Click 16. Compl

36Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingOn LinuxExecuting the commands through the Command Line:# dio_tst The program

37Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingNote: For more details, refer to the README file contained within the progra

38Digital Input/Output ControlAppendix BEmbedded and Industrial Computing#include <string.h>#define delay(x) usleep(x)#endif#ifdef MODULE#includ

39Digital Input/Output ControlAppendix BEmbedded and Industrial Computing{ outportb(INDEX_PORT, 0x07); //LDN register delay(5); outpor

4IntroductionChapter 1Embedded and Industrial ComputingChapter 1: IntroductionThank you for choosing the LEC-2110. The LEC-2110 features On-b

40Terms and ConditionsAppendix GEmbedded and Industrial ComputingAppendix G: Terms and ConditionsWarranty Policy All products are under warran

41Terms and ConditionsAppendix GEmbedded and Industrial ComputingRMA Service Request Form When requesting RMA service, please fill out the following

5IntroductionChapter 1Embedded and Industrial ComputingPackage ContentsYour package contains the following items:LEC-2110 Fanless Embedded System •Ser

6System ComponentsChapter 2Embedded and Industrial ComputingChapter 2: System ComponentsSystem DrawingMechanical dimensions of the LEC-2110Unit: mm2

7System ComponentsChapter 2Embedded and Industrial ComputingBlock DiagramThe block diagram depicts the relationships among the interfaces and mo

8System ComponentsChapter 2Embedded and Industrial ComputingFront ComponentsComponent Description Pin Definition ReferenceF1 Power Button with dual L

9System ComponentsChapter 2Embedded and Industrial ComputingRear ComponentsComponent Description Pin Definition ReferenceR1 Two Serial Ports Serial